基礎:電源コードにはどのような仕様がありますか

This article focuses on :Specifications power cords

A power line is a cable that brings electric present. Typically the current is transmitted in a point-to-point fashion. Power cords can be separated right into air conditioner power cords as well as DC power cords according to their use. Normally air conditioner power cables are cables that pass through greater voltages of alternating present, which call for unified criteria to get safety certification before they can be formally produced. .

The DC line is essentially via the lower voltage DC, so the safety and security needs are not as strict as the air conditioning line, specifications power cords but also for security reasons, nations still require unified security accreditation.

specifications power cords

The performance indications of twisted pair wires in power line

For twisted set cable televisions, the customer is most interested in several signs that qualify their efficiency. These indications consist of attenuation, near-end crosstalk, insusceptibility features, distributed capacitance, DC resistance, 等.

What are the requirements of the power cord

(1) Depletion

Attenuation (Attenuation) is a measure of signal loss along a link. Depletion is connected to the size of the cable television, and also as the length raises, the signal attenuation additionally increases. Attenuation is measured in “db” and represents the ratio of signal toughness from the source to the receiver. As depletion differs with frequency, it must be measured over the full range of frequencies in the application.(specifications power cords)

(2) Near-end crosstalk

Crosstalk is separated into near-end crosstalk and far-end crosstalk (FEXT).specifications power cords, specifications power cords,The tester generally measures NEXT, which has much less influence on the FEXT worth due to the presence of line loss. Near-end crosstalk (NEXT) loss is the dimension of the signal coupling from one set of cables to one more in a UTP link. NEXT is a key efficiency indication for UTP web links as well as is just one of the most challenging to measure precisely.

As the signal frequency boosts, it ends up being more difficult to determine. NEXT does not suggest the amount of crosstalk produced at the near end point, however only the quantity of crosstalk measured at the close to end point. This value differs with the size of the cable, the longer the cable television, the smaller sized the worth ends up being.

At the same time the signal at the transmitter end is undermined and also the crosstalk to other sets comes to be reasonably little. Experiments have actually revealed that the NEXT is just reasonable when measured within 40 metres. If the various other end is further than 40 metres from the info outlet, then there is a degree of crosstalk, which may not be gauged by the tester. したがって, it is best to gauge NEXT at both ends. Today’s testers are outfitted to ensure that the NEXT worth at both ends can be determined at one end of the web link.

(3) DC resistance

This parameter is not readily available for the TSB67. The DC loophole resistance eats part of the signal and also turns it into heat. It is the sum of the resistance of a set of wires,
The DC resistance of a twisted pair of cords of dimension 11801 should not be greater than 19.2 ohms. The distinction in between each set must not be too huge (未満 0.1 ohm), specifications power cords or else it indicates that the call is poor and also the connection point should be checked.

(4) Characteristic insusceptibility

Various from the loophole DC resistance, characteristic resistance consisting of resistance and also regularity of 1 to 100MHz inductive insusceptibility and capacitive insusceptibility, which is related to the range in between a set of cords and also the electrical homes of the insulator.
Numerous wires have various particular insusceptibility, while twisted pair cable televisions have 100 ohms, 120 ohms and also 150 ohms several.

(5) depletion crosstalk proportion (ACR)

In some frequency ranges, crosstalk as well as depletion of the percentage of the partnership is to show the efficiency of the wire an additional essential specification,.
A larger ACR value implies greater immunity to disturbance. Normally systems call for a minimum of 10 dB.specifications power cords

(6) Wire features

The top quality of a communication channel is described by its wire characteristics; SNR is a procedure of the stamina of the information signal, taking into consideration interfering signals. If the SNR is as well low,.

If the SNR is too low, the data signal is obtained as though the receiver can not compare the information signal as well as the sound signal, which inevitably causes data errors. For that reason, in order to limit the information errors to a particular variety,.

A minimal appropriate SNR has to be specified.
specifications power cords Commonly made use of cord sizes for residential setups are: 1, 1.5, 2.5, 4, 6, 10, 16, 25, 35, 50, 70, 95, 120, 150, 185, 240, 300, 400, 500 mm ².
また: e.g.
VV4X16MM2 is PVC protected, PVC encased copper core cable, 4 コア, 16 square each.
BV1X95MM is a PVC protected copper core cable with a random sample of 95 sq. IECタイプGプラグアンドソケットとは.

RVV3X2.5 MM2– Normally R is added to the back to stand for “multi-core flexible cord”, and the one contributed to the front is usually “ZR”, standing for fire resistant.

VV is polyvinyl chloride protected, PVC covered wire.
BV is flat polyvinyl chloride sheathed cord.
RVV is a polyvinyl chloride protected, polyvinyl chloride sheathed versatile wire.
The last represents the severe cross-sectional location of numerous copper wires.

Normally copper core cord by 1mm2 can pass 4 ~ 6A current calculation, あれは, 1mm2 can pass 5A current, あれは, 1.1 kilowatts, and more; as a whole, the a/c hanging equipment with 2.5, closet maker with 4, lighting on the line with 1.

DCpowercordはプロです 適切なDC電源延長ケーブルを選択する方法. 電源コードについてご不明な点がございましたら、当社のエンジニアがお答えします。. 直接お問い合わせください!

DCpowercordYoutubeチャンネル